Onboard Air Systems

Equipment

Transportation

Home > Road Side Assistance > Compressor > Onboard Air Systems

We found 12 results matching your criteria.

Sort By:

Page of 2

Ultra-Light Duty Onboard Air System (12V, 105 PSI Compressor, 1.0 Gal. Tank)

Ultra-Light Duty Onboard Air System (12V, 105 PSI Compressor, 1.0 Gal. Tank)

Our Price: $181.93

Ultra Light Duty Onboard Air System can be used to pressurize the included 1.0 gallon air tank for air horn use, off road air locking differential use, and a host of other light duty pneumatic needs.
While not intended to inflate tires, this onboard air system provides
a reliable smaller volume, in a cost effective package.

Please Note: Use thread sealant for proper installation.
Teflon tape is not recommended.
Properly sealed, recommended torque for 1/8" is 10 ~ 11 ft. lbs. Recommended torque for 1/4" and 3/8" is 16 ~ 18 ft. lbs. Included Parts:
- 1.0 Gallon VIAIR Air Tank
- 98C VIAIR Air Compressor
- Omega Bracket with Mounting Hardware
- Pressure Switch (85 PSI on, 105 PSI off)
- 40-amp Relay
- 145 PSI Safety Valve
- T-Fitting: 1/4� (M) x 1/4" (F) x 1/8� (F)
- T-Fitting: 1/4� (M) x 1/4" (F) x 1/4� (F)
- 1/4� Drain Cock
- 1/4� Compression Fitting
- 1/4� Plug (M)
- (2) 1/4� (M) NPT to 1/8� (F) BSP
- 20ft. 12 Gauge Wire with Inline Fuse Holder
- Accessory Airline
- Electrical Connections

Quarter Duty Onboard Air System (12V, 120 PSI Compressor, 2.0 Gal. Tank)

Quarter Duty Onboard Air System (12V, 120 PSI Compressor, 2.0 Gal. Tank)

Our Price: $251.93

Quarter Duty Cycle Onboard Air System is a smaller, 120 psi onboard air system, suitable for many pneumatic needs, including smaller inflation tasks (not including the inflation of automotive tires), air horns and more. The 25% Duty Cycle Onboard Air System will provide enough service time to operate for about 10 minutes of continued use, providing you give the system 30 minutes to cool down afterwards.

Please Note: Use thread sealant for proper installation.
Teflon tape is not recommended.
Properly sealed, recommended torque for 1/8" is 10 ~ 11 ft. lbs. Recommended torque for 1/4" and 3/8" is 16 ~ 18 ft. lbs. Included Parts:
- 2.0 Gallon VIAIR Air Tank
- 275C VIAIR Air Compressor
- Pressure Switch (90 PSI on, 120 PSI off)
- 40-amp Relay
- 145 PSI Safety Valve
- 1/4� Drain Cock
- 1/4� Compression Fitting
- 20ft. 12 Gauge Wire with Inline Fuse Holder
- Accessory Airline
- Electrical Connections Specifications: - 12-Volt
- Permanent Magnetic Motor
- Duty Cycle: 25% @ 100 PSI
- Max. Working Pressure: 120 PSI
- Max. Amp Draw: 20 Amps
- Ingress Protection Rating: IP54

Medium Duty Onboard Air System (12V, 150 PSI Compressor, 2.5 Gal. Tank)

Medium Duty Onboard Air System (12V, 150 PSI Compressor, 2.5 Gal. Tank)

Our Price: $405.93

VIAIRs Medium Duty Onboard Air System is a pre-packaged compressed air solution that provides a 33% duty cycle 325C compressor, 2.5 gallon air tank, and all components needed to
install basic vehicle-based pneumatics.

Please Note: Use thread sealant for proper installation.
Teflon tape is not recommended.
Properly sealed, recommended torque for 1/8" is 10 ~ 11 ft. lbs. Recommended torque for 1/4" and 3/8" is 16 ~ 18 ft. lbs.
Included Parts:
- 2.5 Gallon VIAIR Air Tank
- 325C VIAIR Compressor
- Dash Panel Gauge with ON/OFF Switch
- Pressure Switch with Relay (110 PSI on, 145 PSI off)
- Reducer: 1/8� (F) to 1/4� (M)
- 1/4� Quick Connect Coupler (M)
- 1/4� 175 PSI Safety Valve
- 1/4� Drain Cock
- 20ft. 12-Gauge Wire with Inline Fuse Holder
- 4� Strip of Continuous Grommet Material
- Accessory Airline
- Electrical Connections
Specifications: - 12-Volt
- Permanent Magnetic Motor
- Duty Cycle: 33% @ 100 PSI
- Max. Working Pressure: 150 PSI
- Max. Amp Draw: 21 Amps
- Ingress Protection Rating: IP67

Heavy Duty Onboard Air System (12V, 150 PSI Compressor, 2.5 Gal. Tank)

Heavy Duty Onboard Air System (12V, 150 PSI Compressor, 2.5 Gal. Tank)

Our Price: $525.00

VIAIRs Heavy Duty Onboard Air System is a pre-packaged compressed air solution that provides a faster 33% duty cycle 400C compressor, 2.5 gallon air tank, and all components needed to install a working system capable of inflating tires right out of the box.

Please Note: Use thread sealant for proper installation.
Teflon tape is not recommended.
Properly sealed, recommended torque for 1/8" is 10 ~ 11 ft. lbs. Recommended torque for 1/4" and 3/8" is 16 ~ 18 ft. lbs.

Included Parts:
- 2.5 Gallon VIAIR Air Tank
- 400C VIAIR Compressor
- 35ft. Coil Hose with Tire Chuck
- 1/4� Quick Connect Stud (F)
- 1/4� Quick Connect Coupler (F)
- Dash Panel Gauge with ON/OFF Switch
- Pressure Switch with Relay (110 PSI on, 145 PSI off)
- Reducer: 1/8� (F) to 1/4� (M)
- 1/4� 175 PSI Safety Valve
- 1/4� Drain Cock
- (3) 1/4� Compression Fittings
- 20ft. 12-Gauge Wire with Inline Fuse Holder
- 4� Strip of Continuous Grommet Material
- Accessory Airline
- Electrical Connections
Specifications: - 12-Volt
- Permanent Magnetic Motor
- Duty Cycle: 33% @ 100 PSI
- Max. Working Pressure: 150 PSI
- Max. Amp Draw: 30 Amps
- Ingress Protection Rating: IP67

Constant Duty Onboard Air System (12V, 150 PSI Compressor, 2.5 Gal. Tank)

Constant Duty Onboard Air System (12V, 150 PSI Compressor, 2.5 Gal. Tank)

Our Price: $550.00

VIAIRs Constant Duty Onboard Air System is a pre-packaged compressed air solution that provides a 100% duty cycle 450C compressor, 2.5 gallon air tank, and all components needed to install a working system capable of inflating tires.

Please Note: Use thread sealant for proper installation.
Teflon tape is not recommended.
Properly sealed, recommended torque for 1/8" is 10 ~ 11 ft. lbs. Recommended torque for 1/4" and 3/8" is 16 ~ 18 ft. lbs. Included Parts:
- 2.5 Gallon VIAIR Air Tank
- 450C VIAIR Compressor
- 35ft. Coil Hose with Tire Chuck
- Dash Panel Gauge with ON/OFF Switch
- Pressure Switch with Relay (110 PSI on, 145 PSI off)
- Reducer: 1/8� (F) to 1/4� (M)
- 1/4� Quick Connect Stud (F)
- 1/4� Quick Connect Coupler (F)
- 1/4� 175 PSI Safety Valve
- 1/4� Drain Cock
- (3) 1/4� Compression Fittings
- 20ft. 12-Gauge Wire with Inline Fuse Holder
- 4� Strip of Continuous Grommet Material
- Accessory Airline
- Electrical Connections
All Fittings are NPT rated unless otherwise noted. Specifications: - 12-Volt - Permanent Magnetic Motor
- Duty Cycle: 100% @ 100 PSI
- Max. Working Pressure: 150 PSI
- Max. Amp Draw: 23 Amps
- Ingress Protection Rating: IP67

200 PSI Ultra Duty Onboard Air System (12V, 200 PSI Compressor, 2.5 Gal Tank)

200 PSI Ultra Duty Onboard Air System (12V, 200 PSI Compressor, 2.5 Gal Tank)

Our Price: $657.93

VIAIRs Ultra Duty Onboard Air System is a pre-packaged compressed air solution that provides an industry-leading, 200 PSI rated, 100% duty cycle 480C compressor, 2.5 gallon air tank, and all components needed to install a working system capable of inflating tires of virtually any size.

Please Note: Use thread sealant for proper installation.
Teflon tape is not recommended.
Properly sealed, recommended torque for 1/8" is 10 ~ 11 ft. lbs. Recommended torque for 1/4" and 3/8" is 16 ~ 18 ft. lbs.

Included Parts:
- 2.5 Gallon 200 PSI VIAIR Air Tank
- 480C Chrome VIAIR Air Compressor
- Tire Inflation Gun with 200 PSI Gauge
- Dash Panel Gauge with ON/OFF Switch
- 30ft. Coil Hose with Quick Connects
- Pressure Switch (165 PSI on, 200 PSI off)
- Reducer: 1/8� (F) to 1/4� (M)
- Reducer: 3/8� (F) to 1/4� (M)
- 1/4� Quick Connect Stud (F)
- 1/4� Quick Connect Coupler (F)
- 1/4� 250 PSI Safety Valve
- 1/4� Drain Cock
- (3) 1/4� Compression Fittings
- 20ft. 12-Gauge Wire with Inline Fuse Holder
- 4� Strip of Continuous Grommet Material
- Accessory Airline
- Electrical Connections
All Fittings are NPT rated unless otherwise noted.

Recommended Components:
- Pressure Regulator (P/N 90150)
- Mounting Bracket (P/N 95900)

Specifications:
- 12-Volt
- Permanent Magnetic Motor
- Duty Cycle: 100% @ 100 PSI
- Max. Working Pressure: 200 PSI
- Max. Amp Draw: 23 Amps
- Ingress Protection Rating: IP67

Super Duty Onboard Air System (12V, 150 PSI Compressors, 2.0 Gal. Tank)

Super Duty Onboard Air System (12V, 150 PSI Compressors, 2.0 Gal. Tank)

Our Price: $699.93

VIAIRs Super Duty Onboard Air System is a pre-packaged compressed air solution that provides two fast 325C, 33% duty cycle compressors, a 2.0 gallon air tank, inline pressure regulation, and all components needed to install a working system capable of inflating tires, managing air locking differentials, and more.

Please Note: Use thread sealant for proper installation.
Teflon tape is not recommended.
Properly sealed, recommended torque for 1/8" is 10 ~ 11 ft. lbs. Recommended torque for 1/4" and 3/8" is 16 ~ 18 ft. lbs.

Included Parts:
- 2.0 Gallon VIAIR Air Tank
- (2) 325C VIAIR Compressors
- 30ft. Coil Hose with Quick Connects
- Tire Inflation Gun with 200 PSI Gauge
- Dash Panel Gauge with ON/OFF Switch
- 0-220 PSI Pressure Regulator
- Blow Gun Air Tool
- Sealed Pressure Switch (110 PSI on, 145 PSI off)
- (2) 40-amp Relays
- (2) T-Fittings (1/4� (M) x 1/4" (F) x 1/8� (F))
- 1/4� Quick Connect Stud (F)
- 1/4� Quick Connect Coupler (F)
- 1/4� 175 PSI Safety Valve
- 1/4� Drain Cock
- (2) 1/8� BSP to 1/4� NPT
- (4) 1/4� Compression Fittings
- 20ft. 12-Gauge Wire with Inline Fuse Holder
- 4� Strip of Continuous Grommet Material
- Accessory Airline
- Electrical Connections

All Fittings are NPT rated unless otherwise noted.

Specifications:
- 12-Volt
- Permanent Magnetic Motor
- Duty Cycle: 33% @ 100 PSI
- Max. Working Pressure: 150 PSI
- Max. Amp Draw: 40 Amps
- Ingress Protection Rating: IP67

X'treme Duty Onboard Air System (12V, 150 PSI Compressors, 2.0 Gal. Tank)

X'treme Duty Onboard Air System (12V, 150 PSI Compressors, 2.0 Gal. Tank)

Our Price: $769.93

VIAIRs Xtreme Duty Onboard Air System is a pre-packaged compressed air solution that provides two 350C, 100% duty cycle compressors, a 2.0 gallon air tank, inline pressure regulation, and all components needed to install a working system capable of inflating tires, managing air locking differentials, and more.

Please Note: Use thread sealant for proper installation.
Teflon tape is not recommended.
Properly sealed, recommended torque for 1/8" is 10 ~ 11 ft. lbs. Recommended torque for 1/4" and 3/8" is 16 ~ 18 ft. lbs.

Included Parts:
- 2.0 Gallon VIAIR Air Tank
- (2) 350C VIAIR Compressors
- 30ft. Coil Hose with Quick Connects
- Tire Inflation Gun with 200 PSI Gauge
- Dash Panel Gauge with ON/OFF Switch
- 0-220 PSI Pressure Regulator
- Blow Gun Air Tool
- Sealed Pressure Switch (110 PSI on, 145 PSI off)
- (2) 40-amp Relays
- (2) T-Fittings (1/4� (M) x 1/4" (F) x 1/8� (F))
- 1/4� Quick Connect Stud (F)
- 1/4� Quick Connect Coupler (F)
- 1/4� 175 PSI Safety Valve
- 1/4� Drain Cock
- (2) 1/8� BSP to 1/4� NPT
- (4) 1/4� Compression Fittings
- 20ft. 12-Gauge Wire with Inline Fuse Holder
- 4� Strip of Continuous Grommet Material
- Accessory Airline
- Electrical Connections
All Fittings are NPT rated unless otherwise noted.

Specifications:
- 12-Volt
- Permanent Magnetic Motor
- Duty Cycle: 100% @ 100 PSI
- Max. Working Pressure: 150 PSI
- Max. Amp Draw: 40 Amps
- Ingress Protection Rating: IP67

Dual 380C Onboard Air System (200 PSI 2.54 CFM 44 Amp 12V 2.5 Gal. Tank)

Dual 380C Onboard Air System (200 PSI 2.54 CFM 44 Amp 12V 2.5 Gal. Tank)

Our Price: $839.93

VIAIRs Dual 380C Onboard Air System is a pre-packaged compressed air solution that provides two 380C, 100% duty cycle compressors, a 2.5 gallon air tank, inline pressure regulation, and all components needed to install a working system capable of inflating tires, managing air locking differentials, and more.

Please Note: Use thread sealant for proper installation.
Teflon tape is not recommended.
Properly sealed, recommended torque for 1/8" is 10 ~ 11 ft. lbs. Recommended torque for 1/4" and 3/8" is 16 ~ 18 ft. lbs.

Included Parts:
- 2.5 Gallon 200 PSI VIAIR Air Tank
- (2) 380C VIAIR Compressors
- 30ft. Coil Hose with Quick Connects
- Tire Inflation Gun with 200 PSI Gauge
- 0-220 PSI Pressure Regulator
- Sealed Pressure Switch (165 PSI on, 200 PSI off)
- (2) 40-amp Relays
- Inline Fuse Holder
- 1/4� Quick Connect Coupler (M)
- 1/4� 250 PSI Safety Valve
- 1/4� Drain Cock
- (2) 1/8� BSP to 1/4� NPT
- (3) 1/4� Compression Fittings
- 5 Pc. 1/4� NPT Plugs Kit
- 6-Port Billet Manifold with Mounting Bracket (1/4�)
- (2) 15ft. 1/4� Air Line Included
- Electrical Connections

All Fittings are NPT rated unless otherwise noted.

Specifications:
- 12-Volt
- Permanent Magnetic Motor
- Duty Cycle: 100% @ 100 PSI
- Max. Working Pressure: 200 PSI
- Max. Amp Draw: 44 Amps
- Ingress Protection Rating: IP67

Dual 400C Onboard Air System (4.55 CFM 150 PSI 60 Amp 12V 2.0 Gal. Tank)

Dual 400C Onboard Air System (4.55 CFM 150 PSI 60 Amp 12V 2.0 Gal. Tank)

Our Price: $839.93

VIAIRs Dual 400C Onboard Air System is a pre-packaged compressed air solution that provides two 400C, 33% duty cycle compressors, a 2.0 gallon air tank, inline pressure regulation, and all components needed to install a working system capable of inflating tires, managing air locking differentials, and more.

Please Note: Use thread sealant for proper installation.
Teflon tape is not recommended.
Properly sealed, recommended torque for 1/8" is 10 ~ 11 ft. lbs. Recommended torque for 1/4" and 3/8" is 16 ~ 18 ft. lbs.

Included Parts:
- 2.0 Gallon 150 PSI VIAIR Air Tank
- 2) 400C VIAIR Compressors
- 30ft. Coil Hose with Quick Connects
- Tire Inflation Gun with 200 PSI Gauge
- 0-220 PSI Pressure Regulator
- Sealed Pressure Switch (110 PSI on, 145 PSI off)
- (2) 40-amp Relays
- Inline Fuse Holder
- 1/4� Quick Connect Coupler (M)
- 1/4� 175 PSI Safety Valve
- 1/4� Drain Cock
- (2) 1/8� BSP to 1/4� NPT
- (3) 1/4� Compression Fittings
- 5 Pc. 1/4� NPT Plugs Kit
- 6-Port Billet Manifold with Mounting Bracket (1/4�)
- (2) 15ft. 1/4� Air Line Included
- Electrical Connections

All Fittings are NPT rated unless otherwise noted.

Specifications:
- 12-Volt
- Permanent Magnetic Motor
- Duty Cycle: 33% @ 100 PSI
- Max. Working Pressure: 150 PSI
- Max. Amp Draw: 60 Amps
- Ingress Protection Rating: IP67